Schon Kunde?Already a customer? Direkt zu meinem Kundenkonto →Straight to my account → Noch kein Kunde?Not a customer yet? Kostenlos im KNX Shop holen →Get it free in the KNX Shop →
NeuNew KNX Secure: Gerätezertifikate vom mobilen EndgerätKNX Secure: device certificates from your mobile device
ETS5 & ETS6 · lokaler MCP-Connector mit Decision LayerETS5 & ETS6 · local MCP connector with Decision Layer KNX Smart Linking ready

Aus deinen Unterlagen wird das KNX-Projekt.

Your documents become the KNX project.

Der ETS Power Editor ist ein vollwertiger intelligenter KNX MCP Server für die ETS5 und ETS6.

The ETS Power Editor is a full, intelligent KNX MCP server for ETS5 and ETS6.

Leistungsverzeichnis, Verteilerplan, Raumliste, die Mail vom Kunden — leg deiner KI hin, was du ohnehin hast. Der ETS Power Editor, eine ETS-App aus dem offiziellen KNX Shop, gibt ihr die Hände dazu: einen Connector direkt in deiner ETS. Damit arbeitet deine KI live an dem Projekt, das du gerade offen hast — Geräte, Gruppenadressen, Parametrierung. Was in deinen Unterlagen nicht steht, fragt sie.

The bill of quantities, the board plan, a room list, the customer’s email — hand your AI what you already have. The ETS Power Editor, an ETS app from the official KNX Shop, gives it the hands for it: a connector right inside your ETS. With it, your AI works live on the project you currently have open — devices, group addresses, parametrisation. Whatever is not in your documents, it asks about.

Läuft nur auf deinem RechnerRuns only on your PC Startet im Nur-Lesen-ModusStarts in read-only mode Zugang nur mit SchlüsselAccess only with a key
Von dir bis zur AnlageFrom you to your installationlive & lokallive & local
DuYousagst, was daraus werden sollsay what you want
Deine KI-AppYour AI appliest deine Unterlagenreads your documents
Decision Layer
ETS Power Editorprüft die Anfragen der KIchecks the AI’s requests
PlanungPlanningwas sich ändern musswhat has to change
WissenKnowledgewas ein Gerät kannwhat a device can do
AbsicherungSafeguardswas du erlaubt hastwhat you have allowed
Deine ETSYour ETSmit deinem offenen Projektwith your open project
ETS-ZugriffETS accessdein Projekt bearbeitenedit your project
ETS-ProjektETS projectStruktur & Adressenstructure & addresses
Bus-ZugriffBus accesslive mit Geräten redentalk to devices live
Deine AnlageYour installationechte Geräte am Busreal devices on the bus
Der UnterschiedThe difference

MCP ist nur ein Übertragungsprotokoll.
Entscheidend ist der Inhalt, der übertragen wird.

MCP is just a transfer protocol.
What matters is the content being transferred.

Der ETS Power Editor liefert deiner KI Antworten auf ihre Fragen, anstatt ihr das gesamte Lexikon zu übergeben. Seine Antworten entstehen durch deterministische Planung aus den Produktdaten deiner Geräte — nicht durch eine KI, die rät.

The ETS Power Editor gives your AI answers to its questions instead of handing it the entire encyclopedia. Its answers come from deterministic planning based on your devices’ product data — not from an AI that guesses.

Ein kleiner Roboter – die KI – steht mit einem großen Schlüssel in der Hand im Lager eines Elektrogroßhandels, vor endlosen Regalreihen voller Geräte, Kabeltrommeln und Kartons. A small robot – the AI – stands holding a large key in the warehouse of an electrical wholesaler, in front of endless rows of shelves full of devices, cable drums and boxes.

Nur MCP: Deine KI bekommt den Schlüssel zum Lager. Suchen muss sie selbst.

Just MCP: your AI gets the key to the warehouse. It has to do the searching itself.

Derselbe Roboter steht an der Theke und legt die Hand auf eine fertig gepackte Kiste mit grünem Band. Dahinter das Lager. The same robot stands at the counter with its hand on a ready-packed box tied with a green band. Behind it, the warehouse.

ETS Power Editor: Deine KI bekommt, was sie bestellt hat: intelligente Unterstützung und Führung per MCP.

ETS Power Editor: your AI gets what it ordered — intelligent support and guidance via MCP.

KNX Secure Ab ETS Power Editor 1.1.0.7ETS Power Editor 1.1.0.7 or later

Gerätezertifikate vom mobilen Endgerät.

Device certificates from your mobile device.

Du berechtigst die mobilen Endgeräte deines Teams. Deine Mitarbeiter auf der Baustelle scannen damit den Aufkleber gleich beim Einbau — und du holst im Büro live ab, was gescannt wurde: Jedes Zertifikat kommt verschlüsselt beim richtigen Gerät in deinem ETS-Projekt an. Unterwegs kann es niemand lesen, auch unser Server nicht. Hast du Remote-Zugriff auf das Projekt, kannst du das Gerät so sofort programmieren.

You authorise your team’s mobile devices. Your staff on site use them to scan the label right during installation — and at the office you collect live what has been scanned: every certificate arrives, encrypted, at the right device in your ETS project. Nobody can read it along the way, not even our server. If you have remote access to the project, you can program the device straight away.

Remote-InbetriebnahmeRemote commissioning Gescannt, wo das Gerät sitztScanned where the device is Ende-zu-Ende-verschlüsseltEnd-to-end encrypted Keine App-InstallationNo app to install
Auf der Baustelle scannt jemand auf der Leiter den Aufkleber eines Präsenzmelders mit dem mobilen Endgerät. Eine grüne Linie führt vom mobilen Endgerät verschlüsselt über unseren Server, der nichts lesen kann, zum Laptop mit dem ETS Power Editor im Reiter „KNX Secure“. On the building site, someone on a ladder scans the label of a presence detector with their mobile device. A green line runs from the mobile device, encrypted, through our server, which cannot read it, to a laptop showing the ETS Power Editor with the “KNX Secure” tab.
Sieh zu · 1Watch · 1

Du hast die Liste doch schon.

You already have the list.

Behangliste, Verteilerplan, Excel-Tabelle, PDF, eine Notiz — was auf deinem Rechner liegt, liest die KI. Du sagst nur, was daraus werden soll und wo sie anfangen darf. Abtippen musst du nichts.

A blind list, a distribution board plan, a spreadsheet, a PDF, a note — whatever is on your computer, the AI reads it. You only say what you want and where it may start. Nothing needs retyping.

Sieh zu · 2Watch · 2

Der Planer kennt die Reihenfolge.

The planner knows the order.

Geräteparameter hängen voneinander ab — in der ETS siehst du das an der Einrückung: Was eingerückt steht, gibt es erst, wenn die Zeile darüber gesetzt ist. Du nennst nur die Ziele. Die Reihenfolge rechnet der Planer aus, und was schon richtig steht, rührt er nicht an. Das gilt auch für die kniffligen Geräte: ein Smart-Touch-Taster mit seinen Seiten, Kacheln und Funktionen genauso wie ein Kanal am Schaltaktor. Welche Schalter dafür stehen müssen, rechnet der Planer aus dem Anwendungsprogramm des Geräts.

Device parameters depend on each other — in the ETS you can see it in the indentation: whatever is indented only exists once the line above it is set. You only name the targets. The planner works out the order, and whatever is already correct it leaves alone. That holds for the tricky devices too: a smart touch push-button with its pages, tiles and functions just as much as a switch actuator channel. Which switches have to be set for it, the planner works out from the device’s application program.

Sieh zu · 3Watch · 3

Und dann das ganze Haus.

And then the whole house.

Dieselbe Unterlage, nur größer: vier Aktoren, achtundzwanzig Kanäle, vier Geschosse. Was schon verdrahtet ist, bleibt unangetastet. Und wo die KI raten müsste, legt sie es dir vor, statt sich etwas auszudenken.

The same document, just bigger: four actuators, twenty-eight channels, four floors. Whatever is already wired stays untouched. And where the AI would have to guess, it puts the question to you instead of inventing something.

Sieh zu · 4Watch · 4

Manchmal fehlt etwas, das du nicht bestellt hast.

Sometimes something is missing that you didn't order.

Ein Taster, den es im Projekt noch gar nicht gibt — den findet die KI im Katalog und fragt, ob sie ihn holen soll. Und wenn dein Wunsch mit den vorhandenen Geräten gar nicht erfüllbar ist, sagt sie das, schlägt vor, was fehlt, und wartet. Ins Projekt kommt beides erst, wenn du ja sagst.

A push-button that isn't in the project at all — the AI finds it in the catalogue and asks whether it should fetch it. And if what you asked for cannot be done with the devices you have at all, it says so, proposes what is missing, and waits. Neither enters your project until you say yes.

Das PrinzipThe concept

Drei Teile, eine Verbindung — und kein Server von uns dazwischen.

Three parts, one connection — and no server of ours in between.

Der Connector läuft direkt in deiner ETS, nur auf deinem eigenen Rechner. Er ist die Brücke zwischen deiner KI und der ETS. Deshalb sieht die KI genau das Projekt, das du offen hast — in beide Richtungen, ohne Umweg über einen Server von uns.

The connector runs directly inside your ETS, on your own computer only. It is the bridge between your AI and the ETS. That is why the AI sees exactly the project you have open — in both directions, with no detour via a server of ours.

Deine KI-App

Your AI app

Claude Desktop, Cursor, Antigravity oder ChatGPT (Codex) — läuft auf deinem Rechner. Sie liest deinen Projektordner — Verteilerplan, Raumliste, die Mail vom Kunden — versteht daraus dein Vorhaben und plant die nötigen Schritte, bevor irgendetwas geändert wird.

Claude Desktop, Cursor, Antigravity or ChatGPT (Codex) — runs on your computer. It reads your project folder — board plan, room list, the customer’s email — works out your intent from it and plans the necessary steps before anything is changed.

Der Connector

The connector

Die ETS-App in der ETS. Sie setzt jede Absicht in echte ETS-Schritte um, achtet auf deine Freigabe — nur ansehen oder auch ändern — und schreibt mit, was passiert. Dabei reicht sie keine Rohdaten durch: Sie ergänzt sie um ihre Bedeutung — was ein Gerät wirklich kann, was zusammengehört — und entscheidet, welcher Weg in der ETS der richtige ist.

The ETS app inside the ETS. It turns every intent into real ETS steps, respects your permission — view only or also change — and logs what happens. It passes no raw data through: it adds the meaning behind it — what a device can really do, what belongs together — and decides which route through the ETS is the right one.

Dein KNX-Projekt

Your KNX project

Das Projekt, das gerade in deiner ETS offen ist. Änderungen an Geräten, Gruppenadressen und Parametern erscheinen live — nachvollziehbar und im Projekt rückgängig machbar.

The project currently open in your ETS. Changes to devices, group addresses and parameters appear live — traceable and reversible within the project.

Sicherheit & DatenhoheitSecurity & data sovereignty

Deine Projektdaten bekommen wir nicht zu sehen.

We never get to see your project data.

Der Connector läuft allein auf deinem Rechner, und zwischen ihm und deiner KI hängt kein Server von uns. Was deine KI für die jeweilige Aufgabe anfordert, bekommt genau sie — welche KI das ist und wohin sie die Daten weitergibt, entscheidest du mit deiner Wahl und deinem Vertrag dort. Zu Haar-Informatik geht davon nichts. Lesbar erreichen uns nur Rückmeldungen zu Fehlern und Wissenslücken; die kannst du selbst abschicken oder deine KI in deinem Auftrag, und sie lassen sich ganz abschalten. Nutzt du die Gerätezertifikate vom mobilen Endgerät, laufen Geräteliste und Zertifikate über unseren Server — Ende-zu-Ende-verschlüsselt, lesen können wir sie nicht.

The connector runs on your own computer alone, and there is no server of ours between it and your AI. Whatever your AI requests for the task at hand goes to that AI — which one it is, and where it passes the data on, follows from your choice and your contract with its provider. None of it goes to Haar-Informatik. The only thing that reaches us in readable form is feedback on errors and knowledge gaps; you can send it yourself, or your AI can on your behalf, and it can be switched off entirely. If you use device certificates from your mobile device, the device list and the certificates pass through our server — end-to-end encrypted, so we cannot read them.

Kein Server von uns

No server of ours

Der Connector läuft komplett lokal auf deinem Rechner. Zu Haar-Informatik wird dein Projekt nie geschickt, und es hängt kein Server von uns zwischen deiner ETS und deiner KI.

The connector runs entirely locally on your computer. Your project is never sent to Haar-Informatik, and there is no server of ours between your ETS and your AI.

Du sperrst, was privat bleibt

You block what stays private

Kundenname, Vertragsnummer, Zutrittscodes in Geräten: Was du sperrst, wird gar nicht erst zusammengebaut. Wie das geht.

Customer name, contract number, entry codes in devices: whatever you block is never assembled in the first place. How it works.

Erst nur lesen

Read first

Am Anfang darf die KI nur schauen. Etwas ändern kann sie erst, wenn du es in der ETS bewusst erlaubst.

At first the AI may only look. It can change something only once you deliberately allow it in the ETS.

Zugang nur mit Schlüssel

Access only with a key

Ohne den passenden Zugangsschlüssel kommt keine Verbindung zustande. Nur die KI, die du selbst eingerichtet hast, darf mitreden.

Without the matching access key, no connection is established. Only the AI you set up yourself may take part.

Einzelbestätigung

Per-action confirmation

Ab Werk fragt der Connector vor jeder einzelnen Schreibaktion in der ETS nach. Für eine Serie gibst du im selben Fenster zehn Minuten am Stück frei. Vertraust du deiner KI, schaltest du die Rückfrage ab.

Out of the box the connector asks in the ETS before every single write action. For a series you approve ten minutes at a stretch in the same window. Once you trust your AI, you switch the prompt off.

Läuft nur mit offenem Projekt

Runs only with a project open

Der Connector lebt in der ETS-App: keine ETS, kein geöffnetes Projekt — kein Zugang. Hattest du ihn zuletzt an, startet er beim Öffnen wieder mit; ein Haken schaltet das ab, und ein Klick hält ihn jederzeit an.

The connector lives in the ETS app: no ETS, no open project, no access. If it was on last time it starts up again when you open a project; a checkbox turns that off, and one click stops it at any time.

Vollständiges Protokoll

Full log

Jede Verbindung und jede einzelne Aktion wird mitgeschrieben — du kannst jederzeit nachsehen, was die KI getan hat.

Every connection and every single action is logged — you can check at any time what the AI has done.

Projekt und realer Bus sind getrennt. Die meisten Werkzeuge ändern nur das Projekt (offline, rückgängig machbar). Bus-Aktionen wie Download, Adresse programmieren oder Gruppenwerte schreiben wirken sofort am realen Gerät — sie sind gesondert gekennzeichnet, brauchen eine Busverbindung und sind im Read-only-Modus gesperrt.

Project and real bus are separate. Most tools change only the project (offline, reversible). Bus actions such as download, programming an address or writing group values take effect immediately on the real device — they are marked separately, need a bus connection and are blocked in read-only mode.

Rückmeldungen sind das Einzige, was wir zu lesen bekommen. Findest du einen Fehler oder fehlt dir etwas, kannst du es melden: über den Knopf in der ETS-App, dann siehst du den vollen Wortlaut vorher. Oder du bittest deine KI darum — sie ist angewiesen, dir den Text zu zeigen und deine Zustimmung abzuwarten, aber sie ist dein Programm, nicht unseres: erzwingen können wir das nicht. Übertragen werden dein Text, allgemeine Geräteangaben, Fassung und Sprache der App, eine Kennung deiner Installation und, falls du eine einträgst, eine Kontaktangabe — nie Projekt- oder Kundendaten. War das Internet gerade weg, wird die Meldung beim nächsten Öffnen eines Projekts nachgeschickt. Das Senden ist ab Werk an und lässt sich in den Einstellungen ganz abschalten — dann geht keine mehr raus.

Feedback is the only thing we get to read. If you find a bug or something is missing, you can report it: with the button in the ETS app, where you see the full wording beforehand. Or ask your AI to do it — it is instructed to show you the text and wait for your approval, but it is your program, not ours: we cannot enforce that. What is transmitted is your text, general device details, the app's version and language, an identifier for your installation and, if you enter one, a contact detail — never project or customer data. If your internet was down at the time, the report is sent the next time you open a project. Sending is on by default and can be switched off completely in the settings — then none is sent at all.

So arbeitest du mit der KIHow you work with the AI

Ein Projektordner, vier Schritte.

One project folder, four steps.

Du legst pro Bauvorhaben einen Ordner mit deinen Unterlagen an, startest den Connector in der ETS und verbindest ihn mit einem Klick mit deiner KI-App — dann setzt du die KI auf diesen Ordner an.

For each project you create a folder with your documents, start the connector in the ETS and connect it to your AI app with one click — then you point the AI at that folder.

01
Projektordner anlegenCreate a project folder

Leistungsverzeichnis, Verteilerplan, Raumliste — was du ohnehin schon hast.

Bill of quantities, board plan, room list — what you already have.

02
Connector startenStart the connector

Im ETS Power Editor in deiner ETS — zum Kennenlernen erst Read-only.

In the ETS Power Editor inside your ETS — read-only first, to get to know it.

03
Mit deiner KI verbindenConnect your AI

Ein Klick für Claude Desktop, Antigravity, Cursor oder ChatGPT (Codex).

One click for Claude Desktop, Antigravity, Cursor or ChatGPT (Codex).

04
KI ansetzenPoint the AI at it

Ein Satz reicht. Umgesetzt wird erst nach deiner Freigabe.

One sentence is enough. Nothing is changed until you approve.

Zur ganzen AnleitungTo the full guide
Aus der PraxisIn practice

Was du damit machen kannst.

What you can do with it.

Reden statt klicken, Fotos lesen, durchs Gebäude gehen und einsprechen, Fehlersuche am Bus, Abnahme live mit dem Kunden: Zwanzig Arbeitsweisen mit einer KI — von den Grundlagen bis zum fertigen KNX-Projekt — stehen auf einer eigenen Seite.

Talking instead of clicking, reading photos, walking the building and speaking as you go, troubleshooting on the bus, running the acceptance live with the customer: twenty ways of working with an AI — from the basics to the finished KNX project — are on a page of their own.

Ohne KI · Skript-EngineWithout AI · script engine

Lieber direkt aus Excel? Die Skript-Engine.

Prefer working straight from Excel? The script engine.

Neben der KI hat der ETS Power Editor eine Skript-Engine: einfache Befehle, einer pro Zeile, im Stapel ausgeführt — mit getrennter Erfolgs- und Fehlerausgabe. Der Clou: Diese Befehle erzeugst du in Excel, wo du deine Geräte- und Adresslisten ohnehin pflegst. Eine Formel, runterziehen, einfügen, ausführen — fertig ist die halbe Programmierung.

Besides the AI, the ETS Power Editor has a script engine: simple commands, one per line, run as a batch — with separate success and error output. The trick: you generate these commands in Excel, where you keep your device and address lists anyway. One formula, drag down, paste, run — and half the programming is done.

01
Liste in ExcelList in Excel

Deine Geräte, Kanäle, Räume und Adressen — Zeile für Zeile, wie in deiner Dokumentation.

Your devices, channels, rooms and addresses — row by row, as in your documentation.

02
Formel erzeugt BefehleFormula generates commands

Eine Formel setzt aus deinen Spalten die Befehle zusammen — einmal geschrieben, nach unten gezogen.

A formula assembles the commands from your columns — written once, dragged down.

03
EinfügenPaste

Die Befehls-Spalte markieren, kopieren und in die Skript-Engine der ETS-App einfügen.

Select the command column, copy it and paste it into the ETS app's script engine.

04
AusführenRun

Ein Klick — der Editor legt alle Gruppenadressen an und verknüpft sie. Erfolg und Fehler getrennt aufgelistet.

One click — the editor creates all group addresses and links them. Success and errors listed separately.

Zur Skript-EngineTo the script engine
ZukunftssicherFuture-proof
KNX Smart Linking ready

Bereit für die neue KNX-Semantik.

Ready for the new KNX semantics.

Moderne KNX-Geräte beschreiben zunehmend selbst, was jeder Kanal kann und wie er mit anderen zusammenspielt — die Idee hinter dem offiziellen „KNX Smart Linking". Der ETS Power Editor spricht diese Sprache und setzt die passenden Verknüpfungen gleich selbst — er schlägt sie nicht nur vor, er führt sie aus.

Modern KNX devices increasingly describe themselves what each channel can do and how it interacts with others — the idea behind the official "KNX Smart Linking". The ETS Power Editor speaks this language and sets the matching links itself — it doesn't just suggest them, it carries them out.

Und er wartet nicht auf den Standard von morgen: Dieselbe automatische Verknüpfung beherrscht er dank seiner eigenen Wissensbasis schon heute — auch für die vielen Bestandsgeräte, die (noch) keine solche Kennzeichnung tragen.

And it doesn't wait for tomorrow's standard: thanks to its own knowledge base it already masters the same automatic linking today — even for the many existing devices that don't (yet) carry such labelling.

  • Versteht die Hersteller-SemantikUnderstands the manufacturer semanticsNutzt die Angaben moderner Geräte, wo sie vorhanden sind.Uses the information of modern devices where it exists.
  • Setzt die Verknüpfungen selbstSets the links itselfFührt die Links aus — nicht nur als Vorschlag.Carries out the links — not just as a suggestion.
  • Funktioniert schon heuteWorks today alreadyAuch für Geräte ohne Kennzeichnung — dank eigener Wissensbasis.Even for devices without labelling — thanks to its own knowledge base.
VoraussetzungenRequirements

Was du dafür brauchst.

What you need for it.

UmgebungEnvironment
ETS5 oder ETS6 auf WindowsETS5 or ETS6 on Windows

Ein installiertes, lizenziertes ETS5 oder ETS6 mit deinem geöffneten KNX-Projekt.

An installed, licensed ETS5 or ETS6 with your KNX project open.

ETS-AppETS app
ETS Power Editor

Die ETS-App von Haar-Informatik — bringt Skript-Engine und den KI-Connector mit. Du bekommst sie kostenlos im KNX Shop. Die Oberfläche gibt es auf Deutsch, Englisch, Französisch und Spanisch. Dein Projekt lesen und durchsuchen kannst du immer; alles Weitere buchst du bei Haar-Informatik monatlich hinzu. Was es kostet, steht weiter unten.

The ETS app from Haar-Informatik — includes the script engine and the AI connector. You get it free of charge in the KNX Shop. The interface comes in German, English, French and Spanish. Reading and searching your project is always included; everything else can be added monthly through Haar-Informatik. What it costs is further down.

KI-SeiteAI side
Deine KI-App Your AI app

Eine KI-App auf demselben Rechner: Claude Desktop, Antigravity (kostenlos, von Google), Cursor oder ChatGPT (Codex) — mit diesen vieren verbindet sich der ETS Power Editor per Klick. Es geht auch jede andere KI-App, die MCP spricht. Die KI-App selbst kommt nicht von uns: Konto und Kosten laufen bei deinem Anbieter. Alle außer Cursor brauchen einmalig Node.js (kostenlos).

An AI app on the same computer: Claude Desktop, Antigravity (free, from Google), Cursor or ChatGPT (Codex) — the ETS Power Editor connects to those four with one click. Any other AI app that speaks MCP works too. The AI app itself does not come from us: the account and its cost sit with your provider. All but Cursor need Node.js (free) once.

In der ETS5 laufen zwei Dinge anders. Telegramme mitlesen geht dort über den Gruppenmonitor der ETS: starte ihn und wähle unter den Dekodier-Optionen den ETS Power Editor aus — von allein kann die KI in der ETS5 nicht mitlesen. Und eine Produktdatei (.knxprod) in den Katalog holen geht nur in der ETS6. Alles andere ist in beiden Fassungen gleich. Two things work differently in ETS5. Reading telegrams there runs through the ETS group monitor: start it and select the ETS Power Editor under the decoding options — in ETS5 the AI cannot listen in on its own. And pulling a product file (.knxprod) into the catalogue only works in ETS6. Everything else is the same in both versions.
PreisePricing

Was es kostet.

What it costs.

Dein Projekt lesen und durchsuchen kannst du immer. Alles Weitere — vor allem, was dein Projekt oder deine Anlage verändert — buchst du monatlich hinzu und kannst es jeden Monat wieder beenden.

Reading and searching your project is always included. Everything else — above all, anything that changes your project or your installation — can be added monthly and ended any month.

Lesen

Reading

0,00 EUR dauerhaft immer inklusive
EUR 0.00 permanently always included

Dein Projekt lesen und durchsuchen, zusammen mit deiner KI. Der Gruppenmonitor gehört dazu: Telegramme mitlesen und auswerten.

Reading and searching your project, together with your AI. The group monitor is part of it: following and evaluating telegrams.

App in der ETS ausgegraut oder mit Schloss? Dann ist ihre Lizenz aus dem KNX Shop noch nicht aktiviert – in der ETS6 unter Einstellungen → Lizenzierung → Lizenz hinzufügen. Anleitung der KNX →

App greyed out or showing a lock in ETS? Then its licence from the KNX Shop hasn’t been activated yet – in ETS6 under Settings → Licensing → Add a License. KNX guide →

Lesen und Ändern

Reading and changing

24,99 EUR im Monat 3 Monate zum Einstiegspreis · 21,00 EUR netto Die 3 Monate laufen am Stück oder mit Unterbrechungen — ganz wie es passt.
EUR 24.99 per month 3 months at the introductory price · EUR 21.00 net The 3 months run in one go or with interruptions — whichever suits.
49,98 EUR im Monat regulär · 42,00 EUR netto
EUR 49.98 per month regular price · EUR 42.00 net

Monatlich kündbar — jederzeit zum Ende des bezahlten Monats. Damit darf die KI anlegen, verbinden und parametrieren, und der Skript-Reiter schreibt mit. Preise je Lizenz, inkl. 19 % MwSt.

Cancellable monthly — at any time, effective at the end of the paid month. With it the AI may create, link and parametrise, and the script tab writes too. Prices per licence, incl. 19% VAT.

Die KI-App ist darin nicht enthalten — die kommt nicht von uns. Welche du nimmst, entscheidest du; Konto und Kosten laufen bei deinem Anbieter.

The AI app is not included — it does not come from us. Which one you use is your choice; the account and its cost sit with your provider.

KontaktContact

Für KNX-Integratoren, die sauberer und schneller projektieren wollen.

For KNX integrators who want to configure more cleanly and faster.

Der ETS Power Editor ist ein Produkt von Haar-Informatik und wird aktiv weiterentwickelt. Interesse an einem Blick oder einer Zusammenarbeit? Melde dich gern.

The ETS Power Editor is a product by Haar-Informatik and is actively developed. Interested in a look or a collaboration? Feel free to get in touch.

Zirndorf, DeutschlandZirndorf, Germany haar-informatik.de